Kokoelma: Intubaatioputket

• Intubaatioputkiteline, johon mahtuu 16 kpl putkia. 
• Teline on sopiva 2,5 mm - 12 mm intubaatioputkille. 

Koot: 

3 mm, 14 fr | 4mm, 18 fr | 5mm, 20 fr | 6mm, 28 fr | 7mm, 30 fr | 8mm, 33 fr | 9mm, 37 fr | 10mm, 43 fr | 11mm, 47 fr | 12mm, 51 fr | 14mm, 57 fr

• Endotracheal tube with inflatable cuff – Connector included
• Lateral murphy eye at distal tip
• Sizes 3mm to 14mm
• Fully transparent

Silicone Material Benefits:

• Patient comfort. Silicone is a soft material that conforms to body contours. The soft distal tip lessens the chance for any airway tissue damage.
• Reusability. Intended to be used over and over again. Silicone resists deterioration better than PVC or red rubber
• Transparent. See any blood and mucous if they develop.

NOTE: Not autoclavable. Radiolucent

Koot: 4.5 mm x 22 cm | 5.5 mm x 27 cm | 12.0 mm x 48 cm | 14 mm x 36 cm | 16 mm x 36 cm

KRUUSE high quality endotracheal tubes can be sterilized by autoclaving providing that temperature does not exceed 134 degrees Celcius or they can be sterilized by ethylene oxide. Dry heat sterilization should NOT be used.

• I.D. 14mm - O.D. 19 mm - L. 57 cm
• I.D. 16mm - O.D. 22 mm - L. 70 cm
• I.D. 18mm - O.D. 24 mm - L. 75 cm
• I.D. 20mm - O.D. 26 mm - L. 90 cm
• I.D. 22mm - O.D. 30 mm - L. 90 cm
• I.D. 24mm - O.D. 32 mm - L. 90 cm
• I.D. 26mm - O.D. 35 mm - L. 100 cm
• I.D. 28mm - O.D. 39 mm - L. 100 cm
• I.D. 30mm - O.D. 42 mm - L. 100 cm

• Cuffed Silicone endotracheal tube used to deliver anaesthetic gases after oral intubation into the desired position
• The inflated balloon cuff prevents gas loss during assisted respiration

Koot: 

ID 18 mm, L 105 cm | ID 20 mm, L 112 cm | ID 25 mm, L 117 cm | ID 35 mm, L 117cm

KRUUSE high quality endotracheal tubes can be sterilized by autoclaving providing that temperature does not exceed 134º C or they can be sterilized by ethylene oxide. Dry heat sterilization should NOT be used. 

Prevent accidental aspiration
Aspir-Guard prevents fluids and dental debris from being accidentally aspirated during a routine dental procedure.
Numerous publications and textbooks state that the standard of care requires the use of a material to block the oropharynx from accidental aspiration of fluids that accumulate during every dental procedure.
Aspir-Guard is a dehydrated PVA donut shaped product. When rehydrated, it has a soft gentle sponge like feel. It is placed over the distal end of the ET tube prior to intubation just outside the epiglottis. Attached strings are used to tie the Aspir-Guard to the roll gauze or old IV tubing used to secure the ET tube to the patient.
After the patient is intubated, the Aspir-Guard is pushed into place to block the oropharynx from fluid aspiration. Once the procedure is finished, the Aspir-Guard is removed gently together with the ET tube.

Three of each size to a package. Non-sterile. PVA (Polyvinyl Alcohol)

Set of all 3 sizes includes:

J1494a – small 20mm 30m.        Hole size:  6mm, fits tubes 3.5-6.0mm ID

J1494b –  medium 25mm 40mm.         Hole size: 9mm, fits tubes 6.5-8.0mm ID

J1494c – large 30mm 50mm            Hole size: 12mm, fits tubes 9.0-10.0mm ID

Prevent accidental aspiration
Aspir-Guard prevents fluids and dental debris from being accidentally aspirated during a routine dental procedure.
Numerous publications and textbooks state that the standard of care requires the use of a material to block the oropharynx from accidental aspiration of fluids that accumulate during every dental procedure.
Aspir-Guard is a dehydrated PVA donut shaped product. When rehydrated, it has a soft gentle sponge like feel. It is placed over the distal end of the ET tube prior to intubation just outside the epiglottis. Attached strings are used to tie the Aspir-Guard to the roll gauze or old IV tubing used to secure the ET tube to the patient.
After the patient is intubated, the Aspir-Guard is pushed into place to block the oropharynx from fluid aspiration. Once the procedure is finished, the Aspir-Guard is removed gently together with the ET tube.

Three to a package. Non-sterile. PVA (Polyvinyl Alcohol)

Small
Thickness: 20mm
Diameter: 30mm
Hole Size: 6mm, fits tubes 3.5-6.0mm ID

Medium
Thickness: 25mm
Diameter: 40mm
Hole Size: 9mm, fits tubes 6.5-8.0mm ID

Large
Thickness: 30mm
Diameter: 50mm
Hole Size: 12mm, fits tubes 9.0-10.0mm ID

• Crystal clear PVC
• Valve for Luer and Luer-Lock syringes
• Cupped, atraumatic tip
• With standard connector for connection to the Y-piece
• For single use

ID 2.0 mm, Kuffi Ø 9.0 mm

ID 2.5 mm, Kuffi Ø 9.0 mm

ID 3.0 mm, Kuffi 9.0 mm

ID 3.5 mm, Kuffi 11.00 mm

ID 4.0 mm, Kuffi 13.00 mm

ID 4.5 mm, Kuffi Ø 13.00 mm

ID 5.0 mm, Kuffi Ø 13.0 mm

ID 5.5 mm, Kuffi Ø 18.00 mm

ID 6.0 mm, Kuffi Ø 22.00 mm

ID 6.5 mm, Kuffi Ø 22.00 mm

ID 7.0 mm, Kuffi Ø 25.00mm

ID 7.5 mm, Kuffi Ø 25.0 mm 

ID 8.0 mm, Kuffi Ø 27.00 mm

ID 8.5 mm, Kuffi Ø 27.00 mm

ID 9.0 mm , Kuffi Ø 29.00 mm

ID 9.5 mm, Kuffi Ø 29.00 mm

ID 10.00 mm, Kuffi Ø 29.00 mm

ID 11.00 mm, Kuffi Ø 35.00 mm

ID 12.00 mm, Kuffi Ø 52.00 mm

ID 13.00 mm, Kuffi Ø 52.00 mm